ISO INTERNATIONAL STANDARD 16582 First edition 2002-11-01 Open end blind rivets with break pull mandrel and protruding head Cu/St or Cu/Br or Cu/sSt Rivets aveuglesa rupture de tige a corps ouvert, a tetebombee-Cu/St ouCu/BrouCu/SSt Reference number ISO 16582:2002(E) ISO @ISO2002 ISO16582:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe isa trademarkof AdobeSystems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below ISO2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56·CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.ch Printed in Switzerland ii @ ISo 2002All rights reserved ISO16582:2002(E) Foreword Iso (the International Organization for Standardization)is a worldwide federation of national standards bodies (so liaison with IsO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission(lEC)onallmattersofelectrotechnicalstandardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 3 by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO16582 was preparedby Technical Committee ISO/TC 2, Fasteners Annex A of this International Standard is for information only @ ISO 2002- All rights reserved ii ISO16582:2002(E) INTERNATIONALSTANDARD Open end blind rivets with break pull mandrel and protruding head Cu/St or Cu/Br or Cu/SSt Scope 1 This International Standard specifies dimensional and mechanical characteristics and application data for open end blindrivets withbreakpull mandrel and protrudinghead,witha copperbody (Cu)and eitherasteel (St)orabronze 2 Normative references thisInternational Standard.For datedreferences,subsequentamendmentsto,orrevisions of,any ofthese undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. IsO3269:2000,Fasteners—Acceptanceinspection ISO14588:2000,Blindrivets—Terminologyanddefinitions IsO14589:2000,Blind rivets—Mechanicaltesting 31 Dimensions 3.1 General Symbols and designations of dimensions are specified in ISO 14588. 3.2 Rivet dimensions See Figure 1 and Table 1. @ISO2002-All rights reserved 1 ISO16582:2002(E) upe p k b Figure1Rivetdimensions Table1Rivetdimensions Dimensions in millimetres 3 3,2 4 4,8 nom. d max. 3,08 3,28 4,08 4,88 min. 2,85 3,05 3,85 4,65 Rivet body 6,3 max. 6,7 8,4 10,1 dk min. 5,4 5,8 6,9 8,3 k max. 1,3 1,3 1,7 2 dm max. 2 2 2,45 2,95 Mandrel min. 25 25 25 27 p Blind length Imax + 3,5 Imax + 4 Imax + 4 'max